Drywall repair
Drywall repair: holes, cracks, nail pops and water damage
Most damaged drywall can be repaired rather than replaced: small holes are filled, medium holes get a backed patch, and only soaked, moldy or crumbling board is cut out and replaced. The harder part is finding out why the wall was damaged, so the same spot does not fail again. Tell us what you see, and we call you back to sort out the repair and the kind of licensed contractor it needs.
Can the drywall be patched, or does it need replacing?
Size and condition decide it. The board itself is a layer of gypsum between two sheets of paper, so as long as the gypsum around the damage is firm and dry, a patch will hold. Replacement comes in when the board is soft, swollen, stained through, sagging from a ceiling, or moldy.
Nail holes and dents
Anything up to roughly the size of a coin is filled with joint compound in two or three thin coats, sanded and primed. It is the kind of job that is often bundled with other small items on a handyman repair list.
Holes from a doorknob, a fist or a plumber's opening
Larger holes need something behind them. The installer cuts the damage out to a neat square, adds a wood or metal backer or screws to the studs on each side, sets in a piece of new board the same thickness, then tapes the seams and builds up compound over them. The finished repair is always wider than the hole, because the compound has to be feathered out to blend into the flat wall.
Large sections, ceilings and soaked board
When the damage runs across most of a sheet, or a ceiling is sagging, the usual repair is to cut back to the nearest framing and hang new board. On a ceiling this is heavier, slower work, and the seams are harder to hide because light rakes across them.
What usually causes the damage?
Fixing the surface without the cause is the most common reason a repair shows up again. Before anyone patches, ask what made the damage.
- Water. A brown ring, bubbling paint or a soft spot means a leak from a roof, a pipe, a shower, a toilet or an appliance line. The leak gets fixed first, by the right trade, and the board has to be dry before any patch.
- Movement. Diagonal cracks from the corners of doors and windows, and tape lifting along a seam, often come from the house moving with the seasons or settling. A crack that keeps growing, or doors that start to stick at the same time, is worth a look from someone who can judge the framing.
- Fasteners. Small round bumps in a line are nail or screw pops, where the framing behind has shrunk or the fastener never held tight.
- Impact. Door handles, furniture and moving day. A door stop or bumper keeps the same hole from coming back.
Why is matching the texture the hard part?
Because the eye finds any change in the surface, not the patch itself. Walls in many homes have a sprayed or troweled texture such as orange peel or knockdown, and a smooth patch on a textured wall stands out from across the room. A good drywall finisher tests the texture on scrap first, matches how heavy and how wide the pattern is, and lets it dry before priming. Even then, the repaired spot usually looks right only after the whole wall, corner to corner, gets a fresh coat of paint, because old paint has faded and a touch-up does not match its sheen. That is why many drywall repairs end with the painting contractor step.
Water-damaged drywall and mold
Wet drywall needs to dry fast. The U.S. Environmental Protection Agency's brief guide to mold, moisture and your home advises drying water-damaged areas and items within 24 to 48 hours to prevent mold growth, and notes that porous materials, such as ceiling tiles, may have to be thrown away if they become moldy, because the mold can be hard or impossible to remove completely. Drywall paper and gypsum are porous in the same way.
For size, EPA's page on mold cleanup in your home says that if the moldy area is less than about 10 square feet, roughly a 3 by 3 foot patch, most homeowners can handle the cleanup themselves following its guidelines. Above that, or when the water was sewage or the mold is inside the wall, plan for professional help. In every case, the moisture source has to be fixed first; a new patch over a damp cavity just grows mold again.
Older homes: test before you sand
In older houses, joint compound and sprayed ceiling texture may contain asbestos, and the paint on the wall may contain lead. EPA's guidance on protecting your family from asbestos is to leave material that may contain it alone if it is intact, and never sand, saw or drill it; removal is for trained, accredited professionals. Drywall repair is mostly cutting and sanding, so if the house is older, ask about testing before work starts.
For paint, EPA's Renovation, Repair and Painting program applies to paid work that disturbs paint in homes built before 1978, and the firm doing it must hold EPA's RRP firm credential and use lead-safe work practices. Minor repairs that disturb 6 square feet or less of painted surface per room inside are exempt, but a larger cut-out or a whole wall is not.
Does drywall repair need a licensed contractor in California?
It depends on the size of the job. Work of $1,000 or more in combined labor and materials, or any job that needs a permit, needs a licensed contractor. A single small patch often falls under that line; a ceiling replacement or several rooms of water damage usually does not.
The trade license for this work is the C-9, Drywall, at the Contractors State License Board. CSLB's C-9 description covers a contractor who lays out and installs gypsum wall board, including nonstructural metal framing, and does the taping and texturing that gives the board a continuous smooth or textured surface. When the repair also needs plumbing, a roof fix or new framing, a B, General Building contractor can take the whole job and bring in specialty subcontractors. Our license checking guide shows how to look up either one. In Dallas–Fort Worth, Texas rules apply instead; the Texas part of that guide covers what to check there.
What to send with your request
- Photos of the damage, one close up with something for scale and one from across the room.
- Where it is: wall or ceiling, which room, and whether there is a bathroom or the roof above it.
- What caused it, if you know, and whether that cause has been fixed.
- Whether the board is dry and firm, or still damp, soft or stained.
- The texture on the wall, or a photo taken at an angle so the texture shows.
- The year the house was built, or a rough guess, for the lead and asbestos questions.
Questions to ask before you hire
- What do you think caused this, and does that need another trade first?
- Will you patch or replace, and how far past the damage will you cut?
- How will you match the texture, and is priming and painting included?
- How will you keep dust out of the rest of the house?
- For an older home, will you test for asbestos or lead before cutting or sanding?
- What is your license number, and does it include the C-9 or a B?
Get the scope and price in writing before work starts; our page on home improvement contracts covers what a California contract has to include.
What we do, and what we don't
Sending a drywall repair request is free. We call or email you back to go over the damage, its cause and the kind of licensed contractor that fits, then pass your request to a licensed contractor we work with, who gives you the price and schedule. Contractor Near Me is not a drywall company and does not do the work, and we hold no contractor's license ourselves. Look up the license of anyone you consider before you sign.
Drywall repair
Talk the damaged wall over before you hire
Sending a request is free and commits you to nothing. We call or email you back, go over which kind of licensed contractor fits the work, and pass your request to one we work with.
Tell us about the project
A short note is enough. We call or email you back about it; the request is free and you owe nothing for it.
Questions
Drywall repair questions people ask
Short answers to what people ask us. If yours is not here, call and ask; a request costs nothing.
Talk it over with us
We call or email you back about your project.
Why do nail pops keep coming back after they are filled?
Filling the bump only covers the head of the fastener. If the framing behind it has shrunk or the nail never gripped, it pushes out again. The lasting fix is to drive a drywall screw into the stud just above or below the pop, set or remove the old nail, then fill, sand, prime and paint the spot.
Can wet drywall be dried out instead of replaced?
Sometimes, if it got wet briefly, is still firm and is dried within a day or two, as EPA advises for water-damaged materials. Board that stays soft, sags, crumbles, swells at the seams or shows mold should be cut out and replaced, because porous material that grows mold is hard to clean completely.
Why does the crack above my door keep opening again?
The corners of doors and windows are where a wall flexes most as a house moves with the seasons, so a crack filled with compound alone often returns. A repair that lasts usually cuts the crack open, tapes it and recoats it. If the crack keeps getting wider or doors begin to stick, have the framing looked at first.
Sources: CSLB, C-9 Drywall Contractor; CSLB, What Type of Contractor Do I Need?; CSLB, AB 2622 minor work bulletin (2024); EPA, A Brief Guide to Mold, Moisture and Your Home; EPA, Mold Cleanup in Your Home; EPA, Protect Your Family from Exposures to Asbestos; EPA, Lead Renovation, Repair and Painting Program.